Аппаратная ошибка 03130031 2f26 canon

Коды ошибок, актуальные для Canon imagePROGRAF iPF670, iPF605, iPF770, iPF750, iPF710, iPF650, iPF700, iPF785, iPF610, iPF765, iPF680, iPF760, iPF510, iPF780, iPF600, iPF500, iPF685, iPF720, iPF670e, iPF671, iPF671e (для картриджей PFI-102, PFI-104, PFI-107).

Группы ошибок

Ошибки с кодами и расшифровкой

Ошибки в сервисном режиме

Canon imagePROGRAF Hardware Error 03130031 Introduction

When your Canon imagePROGRAF Plotter is stuck with an on-screen hardware error 0313003, you need to call the service center to get assistance to get your Canon large format printer back into working state. In this printer service guide, we will give you some ideas to decode Hardware Error 03130031 and its subcodes of the 4 digits in the end. You can Buy Printer Spare Parts from here

Decoding the Error 03130031

Since we have detailed documentation about this error, it will be easier for you to diagnose the error. The hard part is, this error is closely related to the ‘print head’ and in most cases, you need to replace it to fix the plotter. To diagnose the error in the right way, we need subcode, which is the last four characters of the error code followed by 03130031, for example, ‘2F51’. The whole error code will look like this, 03130031-2F51. Ca’t find the subcode? Contact us for plotter repair in Dubai

Now you know how to find the sub error code, But how to understand the meaning of the 4-digit code followed by 03130031?

Fixing HP Designjet plotter error codes

Hardware Error 03130031 Codes and their Meaning

The 03130031-[Sub Code] error codes are about 45 variants. They all have different meanings and here is how to clear/fix them.

Below are the list of Hardware Error 03130031 Codes

  03130031-260E – Gap detection failure  

  03130031-2618 – VH voltage error  

  03130031-290A – HDD not connected/not detected  

  03130031-291B – Lift shift timeout  

  03130031-291D – Spur cam sensor detector failure  

  03130031-2E23 – Cutter unit failure  

  03130031-2F13 – A/D converter external trigger output stop  

  03130031-2F14 – ASIC register not writable  

  03130031-2F16 – Mist fan error  

  03130031-2F17 – Platen fan lock detection error  

  03130031-2F1F – Purge sensor error  

  03130031-2F20 – Cap motor cam positioning error  

  03130031-2F22 – Pump shift timeout  

  03130031-2F23 – Purge motor error  

  03130031-2F24 – Cutter shift timeout error  

  03130031-2F25 – Carriage motor HP not detectable  

  03130031-2F26 – Carriage Motion Error  

  03130031-2F27 – Carriage shift timeout  

  03130031-2F28 – Lift shift timeout  

  03130031-2F2A – Cannot detect the LF home position  

  03130031-2F2B – LF operation failure  

  03130031-2F2C – Cassette shift timeout  

  03130031-2F2E – Roll shift timeout  

  03130031-2F3A – Ink supply valve open/close monitor timeout  

  03130031-2F3B – CS communication error  

  03130031-2F3C – LP nip sensor error  

  03130031-2F3D – HP pre-ejection pump motor overload error  

  03130031-2F3E – HP pre-ejection pump motor shift timeout  

  03130031-2F3F – An error other than overload error or shift timeout error  

  03130031-2F46 – The shutter HP sensor did not respond at startup  

  03130031-2F48 – VHT (heater drive power supply for printhead) error  

  03130031-2F49 – Left side printhead  

  03130031-2F4A – Main controller PCB error  

  03130031-2F4D – VHT leak detection error of left printhead  

  03130031-2F4E – VHT leak detection error of right printhead  

  03130031-2F4F – VHT leak detection error of left and right printhead or a single printhead  

  03130031-2F50 – Right side printhead  

  03130031-2F51 – Both printheads  

  03130031-2F52 – Detect that a carriage unit of a legacy model has been mounted  

  03130031-2F53 – Supply valve motor error of the left ink tank  

  03130031-2F54 – Supply valve motor error of the right ink tank  

  03130031-2F6C – Failed self-testing  

  03130031-2F70 – Indication at ink priming error in both sub tanks  

  03130031-2F71 – Indication at ink priming error in the left sub tank  

  03130031-2F72 – Indication at ink priming error in the right sub tank  

  03130031-4027 – Lift shift timeout error

How to fix Canon imagePROGRAF Hardware Error 03130031

Fixing Canon imagePROGRAF Hardware Error 03130031 can be a simple power-cycle or a replacement of very expensive spare parts. The first thing you need to do is to make sure there isn’t any paper stuck inside the Canon imagePROGRAF Plotter. And that the carriage assembly is in the docked state on the right side hand side of the plotter. You can verify this by opening the top cover or the Canon imagePROGRAF Plotter.

The second step is to turn off the Canon Plotter by pressing the power button. You should NEVER unplug the Plotter power code while it is ‘ON’. Once you turn the power off, turn the plotter ‘ON’ in the usual way. If it clears the error message, consider you are lucky and continue your print job as usual. 

If the steps as mentioned above, don’t fix the error, you will need to may need to call Plotter Service Center in Dubai.

1. 09-01-2015

   
   

   #1

   

   
   Technician
   

   

   ---

   Rep Power

   16

   Canon IPF750 hardware error 03130031-2F26
   

   Hi

   I own a Canon IPF750 witch has a error

   03130031-2F26.When i power on the printer, it starts to initialize and then the printhead moves to the left for a distance like abouth 80 cm.
   This is the distance from the starting point completely from the right side.
   When i shut down the printer and move the printhead like 15 cm to the left from the starting point and the turn on the printer again, then the printhead also moves about the same distance to the left. So 80 cm + 15 cm. When the printhead starts from the middle then it moves also to left with a big clunck at the end of the movement (banging against the end of the rail).

   I have cleaned the transport rail and checked the optical ribbon for stains or other malicious substances.

   The weird thing is, that the distance the head moves is almost always exactly the same (like abouth 80 cm).
   Also i cant seem to enter service mode to update the firmware wich is needed to do the upgrade.

   I have disassembled the printhead to see if there is no durt or stains on the optical sensor and/or if the ribbon cables are not broken.
   I don’t see any breaks in the cable (not visually).

   All suggestions are welcome.

   Roverius

   ---

2. 09-01-2015

   
   

   #2

   Re: Canon IPF750 hardware error 03130031-2F26
   

   Originally Posted by Roverius
   

   Hi

   I own a Canon IPF750 witch has a error

   03130031-2F26.When i power on the printer, it starts to initialize and then the printhead moves to the left for a distance like abouth 80 cm.
   This is the distance from the starting point completely from the right side.
   When i shut down the printer and move the printhead like 15 cm to the left from the starting point and the turn on the printer again, then the printhead also moves about the same distance to the left. So 80 cm + 15 cm. When the printhead starts from the middle then it moves also to left with a big clunck at the end of the movement (banging against the end of the rail).

   I have cleaned the transport rail and checked the optical ribbon for stains or other malicious substances.

   The weird thing is, that the distance the head moves is almost always exactly the same (like abouth 80 cm).
   Also i cant seem to enter service mode to update the firmware wich is needed to do the upgrade.

   I have disassembled the printhead to see if there is no durt or stains on the optical sensor and/or if the ribbon cables are not broken.
   I don’t see any breaks in the cable (not visually).

   All suggestions are welcome.

   Roverius

   Carriage is moving to the left and then displays a 2F26.
   There is a

   noise when the Carriage moves to the left-most position.The Feed Roller shaft bushing, shown below, may be broken.
   The Carriage was striking it when moving to the left. Replacing the bushing resolved the issue. QC3-1478-000

   

   ———————————————————————————————-
   or
   iPF750After Power On and at the time of printer initialization while the Carriage Unit has moved to the Left and it starts moving toward Right (home position) printer stops and error 2F26 would show on the control panel display.

   In this case in this iPF750, the following parts were replaced to resolve the problem:
   Pulley Unit (part # QM3-5833-000)
   Spring, Compression (part # QU1-2441-000)
   Retainer, Pulley (part # QC3-1531-000)

   ================================================== =============================

   imagePROGRAF Unusual Noises
   Location	Type of Noise	Cause/Remedy/Action
   Carriage Drive	Rasping	/Check the carriage drive ldler Pulley /Check the Carriage Tension Unit /Refer to the causes for 2F26 errors in the Service Manual and /Trouibleshooting Guide
   Chattering	/Check if the Tube Unit is striking the exterior walls /Try opening and closing the Platen Suction Path Selection Valve (this is normal)
   Creaky	/Make sure the Carriage Rail is dry and not soiled (never apply oil) /Replace the Rail Cleaner /Replace the Carriage Bearing if applicable (large printers only) /Check if the Print Head open/close lever is broken (replace as required)
   Head rubbing	Abrasive	/Check the Print Head height setting /Check for jams in the paper path near the Print Head /Check the Paper Type settings
   Cutter	Chattering	/Replace the Cutter unit if it is damaged
   Near the lnk Tank Unit	Chattering	/The Ink stirring operation is in process (this is normal)
   Roll Spool	Chattering	/Check if the drive belt is loose /Set the Rubber Pad to the correct position
   Paper Feed / Back Feed	Chattering	/Check the LF Backup Roller /Replace as needed
   Caterpillar Mylar	Chattering	/Check if the Catepillar Mylar sheet is out of position /Replace the Tube Unit as required
   Platen Suction Hole	Whistling	/Clean the Platen suction hole

   **Knowledge is time consuming, exhausting and costly for a trained Tech.**

   ---

3. 09-01-2015

   
   

   #3

   

   
   Technician
   

   

   ---

   Rep Power

   16

   Re: Canon IPF750 hardware error 03130031-2F26
   

   Hello,

   Thank you for the reply.

   I will check if that bushing is defective or not.
   Meanwhile i am going to try to make a video and place it on the web for you to see what is happening.

   Regards,
   Roverius

   ---

4. 09-01-2015

   
   

   #4

   

   
   Technician
   

   

   ---

   Rep Power

   16

   Re: Canon IPF750 hardware error 03130031-2F26
   

   Hello again.

   I have checked the bushing and it seems OK.

   I have made a video of the problem:

   I hope this helps to understand the problem.

   Regards,
   Roverius

   ---

5. 09-03-2015

   
   

   #5

   Re: Canon IPF750 hardware error 03130031-2F26
   

   [QUOTE=Roverius;487426]Hi

   I own a Canon IPF750 witch has a error

   03130031-2F26.When i power on the printer, it starts to initialize and then the printhead moves to the left for a distance like abouth 80 cm.
   This is the distance from the starting point completely from the right side.
   When i shut down the printer and move the printhead like 15 cm to the left from the starting point and the turn on the printer again, then the printhead also moves about the same distance to the left. So 80 cm + 15 cm. When the printhead starts from the middle then it moves also to left with a big clunck at the end of the movement (banging against the end of the rail).

   I have cleaned the transport rail and checked the optical ribbon for stains or other malicious substances.

   The weird thing is, that the distance the head moves is almost always exactly the same (like abouth 80 cm).
   Also i cant seem to enter service mode to update the firmware wich is needed to do the upgrade.

   I have disassembled the printhead to see if there is no durt or stains on the optical sensor and/or if the ribbon cables are not broken.
   I don’t see any breaks in the cable (not visually).

   All suggestions are welcome.

   Roverius[/QUOTE

   Hi Roverius,

   I would recommend you replace the Carriage Relay PCB then if that doesn’t change anything its most likely the Main Controller PCB
   
   Hate to tell you this but for me, 9 out of 10 times that I have had this error, it was the Main Controller PCB, and unfortunately its quite expensive to replace, if you have a second hand one to test with first, it would be a lot cheaper than committing to a new board, as once the part is opened canon wont refund you if it doesn’t fix your issue, unless you get a canon tech to fit the part for you.

   hope this helps,

   Cheers,

   SAZ911……….

   ---

6. 09-03-2015

   
   

   #6

   

   
   Technician
   

   

   ---

   Rep Power

   16

   Re: Canon IPF750 hardware error 03130031-2F26
   

   Hi Roverius,

   I would recommend you replace the Carriage Relay PCB then if that doesn’t change anything its most likely the Main Controller PCB
   
   Hate to tell you this but for me, 9 out of 10 times that I have had this error, it was the Main Controller PCB, and unfortunately its quite expensive to replace, if you have a second hand one to test with first, it would be a lot cheaper than committing to a new board, as once the part is opened canon wont refund you if it doesn’t fix your issue, unless you get a canon tech to fit the part for you.

   hope this helps,

   Cheers,

   Hi,

   I am going to try to find the Carriage relay PCB (QM3-4932-000 ) and see what happens.
   Else, maybe i can find a refurbished Main controller PCB.

   Hopefully, i can repair it with the relay pcb, because i dont want to spend to much to repair this printer.

   Regards,
   Roverius

   ---

7. 09-04-2015

   
   

   #7

   

   
   Technician
   

   

   ---

   Rep Power

   16

   Re: Canon IPF750 hardware error 03130031-2F26
   

   Hi,Question:
   The Carriage relay PCB (QM3-4932-000 ), is this the board that looks like a power supply?
   I only see 2 boards, a power supply looking board and a systemboard.

   Also, i hear a high pitched noise at the coverlock. Is this normal.
   Sorry for the questions, but i never had a printer like this before and just got it as a present (well allmost) with the problems included.

   Regards,
   Roverius

   ---

8. 09-04-2015

   
   

   #8

   Re: Canon IPF750 hardware error 03130031-2F26
   

   Originally Posted by Roverius
   

   Hi,

   Question:
   The Carriage relay PCB (QM3-4932-000 ), is this the board that looks like a power supply?
   I only see 2 boards, a power supply looking board and a systemboard.

   Also, i hear a high pitched noise at the coverlock. Is this normal.
   Sorry for the questions, but i never had a printer like this before and just got it as a present (well allmost) with the problems included.

   Regards,
   Roverius

   Hi Roverius,

   The board that looks like a power supply at the back of the machine is the power supply (QK1-5056).
   Carriage pcb unit should be (QM3-4569).
   Main controller should be (QM3-5820).The carriage pcb unit is a small board that is in the Carriage assy that carries the printhead, it connects the ribbon cable from the carriage pcb to the main controller at the back of the machine.

   Please Note:
   Please double check the part numbers as the numbers i have provided are for the European market and so the voltages on the power supply may vary from region to region.
   

   good luck,

   cheers….

   SAZ911……….

   ---

9. 09-04-2015

   
   

   #9

   

   
   Technician
   

   

   ---

   Rep Power

   16

   Re: Canon IPF750 hardware error 03130031-2F26
   

   Originally Posted by SAZ911
   

   Hi Roverius,

   The board that looks like a power supply at the back of the machine is the power supply (QK1-5056).
   Carriage pcb unit should be (QM3-4569).
   Main controller should be (QM3-5820).The carriage pcb unit is a small board that is in the Carriage assy that carries the printhead, it connects the ribbon cable from the carriage pcb to the main controller at the back of the machine.

   Please Note:

   Please double check the part numbers as the numbers i have provided are for the European market and so the voltages on the power supply may vary from region to region.
   

   good luck,

   cheers….

   Hi,

   Thank you for the reply.
   The machine is european, so 220Volt power input.

   I have looked for the cariage pcb, but it seems i can not locate where it is placed.
   I only see 2 boards at the back of the printer w.i. the powerboard and the main pcb board.
   Can you explain where the cariage pcb is located please.

   Regards,
   Roverius

   ---

10. 09-04-2015

    
    

    #10

    Re: Canon IPF750 hardware error 03130031-2F26
    

    Originally Posted by Roverius
    

    Hi,

    Thank you for the reply.
    The machine is european, so 220Volt power input.

    I have looked for the cariage pcb, but it seems i can not locate where it is placed.
    I only see 2 boards at the back of the printer w.i. the powerboard and the main pcb board.
    Can you explain where the cariage pcb is located please.

    Regards,
    Roverius

    Hi

    The board would be just behind where you put the printhead in the carriage assy.(see pic below) Also might be worth replacing the whole carriage assy(QM3-58244).
    roverius.JPG

    * If you haven’t replaced this board before it can be quite a challenge so it may be worth getting a canon tech to have a look at it for you.

    cheers………

    SAZ911……….

    ---

IPF-605 ошибка 2F26

• ← Предыдущая тема
• iPF500, iPF600, iPF605, iPF610, iPF700, iPF710, iPF755, iPF6100, iPF8100
• Следующая тема →